Filter Results By:
Products
Applications
Manufacturers
-
product
Special Purpose Instruments
The Mechanical Impedance Sensor simultaneously measures an applied, driving-point force and response acceleration of a test structure for determining parameters such as mechanical mobility and mechanical impedance. The unit consists of a precision, shear mode accelerometer and a quartz force sensor in a common housing. Installation is primarily facilitated at the structural excitation points, in series with a stinger and vibration shaker.
-
product
Field Test Interface Kit
2200
TESCO’s new Field Test Interface Kit (Catalog No. 2200) provides metering professionals with exceptional testing flexibility. The Field Test Interface includes a zero insertion force (ZIF) meter socket, voltage and form selection, and connection points to link it with a TESCO Field Test Kit (Catalog No. 621, 630 or GA Series). When combined with a Field Test Kit and powered via inverter (commonly used on service trucks), the Field Test Interface will then power the Field Test Kit to create a single position, stand-alone, meter accuracy testing device for various socket based meters (both mechanical & solid-state). Power for the Field Test Interface can also be supplied by customer potential via TESCO Field Test Kit (no need for the inverter).
-
product
Damp-Heat Tester
King Design Industrial Co., Ltd.
1. Technical index:*Power: 380V, 3-, 50/60HZ 110A*Temperature range: 50°C~120°C*Humidity range: 20%~95% RH*Accuracy: 1) temperature ± 0.3°C;2) humidity ± 2.5% RH*Uniformity: 1) temperature ± 2.0°C;2) humidity ± 3.0% RH*Uniformity test: measured at T=85°C, RH=85%; set 9 points for temperature measurement and 2 points for humidity.*Inner wall is above 50 cm; within 20 min after temperature/humidity meets the setting value, the distribution uniformity of temperature/humidity can meet the aforesaid requirement.
-
product
SF6 Leakage Detector
GDWG-IV
GDWG-IV SF6 Gas Leak Detector is infrared type leak detector. It is color LCD display and real-time shows SF6 concentration. It rapidly detect SF6 breaker, GIS leakage point and yearly leakage rate qualitatively and quantitatively. It's a good device suitable for power supply department, installation and overhaul unit, power test institute.
-
product
4x IDC Quadrapaddle
YAV90Q04
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
product
Bench Hardness Tester
MTR X-SERIES
The bench hardness tester MTR X-SERIES operates to determination through the measurement of electrical resistance. The MTR X-SERIES hardness tester has been designed to solve some of the still unsolved issues in the field of hardness control. Its test principle allows the user to perform measurements in difficult or inaccessible points internal surfaces and gear teeth.
-
product
Boundary-Scan Interactive Analyzer & Toolkit
ScanExpress JTAG Debugger
Test probe access is a luxury—modern electronic system design techniques such as blind and buried vias or ball-grid-array (BGA) devices guarantee limited signal access. Test points quickly reduce precious board real-estate and can even degrade performance. ScanExpress JTAG Debugger overcomes these limitations to provide the control and visibility necessary to quickly debug and test hardware, using a simple JTAG port to interface with IEEE-1149.1 compliant devices.Whether debugging prototype hardware, enhancing production tests with boundary-scan control, or diagnosing a faulty board in the field, ScanExpress Debugger’s easy-to-use and versatile interface helps engineers test and debug systems faster and more efficiently.
-
product
Robotic Probing of Circuit Cards
System provides reliable automatic access to test points on a printed circuit under test providing rapid and accurate diagnostic measurements. Accomplished by an automated test probe with video image capability, under control of application software running on a VXI Test System utilizing LabVIEW. A VXI Prober Interface Module (VPIM), developed to Plug and Play standards, provides interface between prober and VXI Test System.
-
product
Calibration Systems
WIKA Alexander Wiegand SE & Co. KG
WIKA's robust and modular calibration systems are designed for checking the SF6 gas density and pressure measuring instruments. The test item is connected to the calibration system via an adapter and, by pressure generation with a hand pump, makes it possible to exactly approach the measuring points. A subsequent comparison of the displayed values of the test item and reference instrument allows assessing the instrument's suitability for on-site use. The instrument is always protected and ready for use with the robust service case and an additional foam insert.
-
product
Keysight Dual/Quad 4x8 Reed Matrix for 34980A
34933A
The Keysight 34933A module for the 34980A Multifunction Switch/Measure Unit gives you the most flexible connection path between your device under test and your test equipment, allowing different instruments to be connected to multiple points on your device under test at the same time. Dual 4x8, 8x8, or 4x16 2-wire configurations 64 2-wire or 128 1-wire cross-points High-speed reed relays Connections to the internal DMM Expandable via four 2-wire analog buses Relay counter ±150 V peak, .5 A switch, 1.5 A carry current
-
product
Receiver, 9025, 25 Module, EMI Gasket
310104431
The 25 Module Receiver is a rugged system devised to accommodate medium I/O. With high contact point availability, the 25 Module Receiver is suited for larger test and measurement systems. This 9025 offers a gasket for EMI applications.
-
product
Voltage Indicators
*Measures voltage from 100V to 138kV line‑to‑line.*Can be used individually as voltage indicators or together for phasing operations up to 100 ft (30 m) apart.*Two LED displays are automatically synchronized during phasing operations.*Clear in-phase and out-of-phase indication.*Versatile for overhead and underground applications.*Capacitive Test Point and Peak Hold modes
-
product
Voltage Detector
Shenzhen Noyafa Electronic CO.,LTD
*Detect AC Power range : 50-1000V.*Test live wire and with flash indicate.*Locate wire break point easily.*LED assist using in dark place.*Certification. Passes RoHS, FCC, and CE compliance testing, and Noyafa is certified to the ISO 9001 standard.*100% Affordable. Manufactured in China and a lot cheaper than competitor products with similar quality.
-
product
BDV Transformer Oil Test Sets
NMC''s Transformer BDV Oil Test Set is a portable unit as per relevant Indian Standard Specification IS :6792 :1992, suitable for operation on 230 / 240 Volts, A.C. 50 Hz. A three core flexible cable is connected to the unit with three pin socket to connect the mains. The H.V. Transformer is a completely dry, resin encapsulated with two H.V. terminals with mounting saddles. The center point of the transformer is earthed, so that the voltage of each terminal to earth is only half the test voltage.
-
product
Gold Probes
4900 Series
The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.
-
product
Design for Test Service
Design For Test (DFT) is a technique used to implement certain testability features into a product. Testing House can provide an analysis of the CAD data for testability of your circuit board. Access to a board can be very difficult as boards get smaller and designs get more densely populated. We can work with your design engineer to improve testability and maintain an effective in-circuit test. When access to the board is limited and boundary scan devices are present, we can provide the customer a list of key nodes that will require access in order to provide a very effective test. Our analysis will provide a list of all the accessible test points and an explanation for any nodes declared inaccessible.
-
product
Plugbord
3682
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.Interleaved buses pattern on wiring side only solder- coated for user convenience. Bus outline silkscreened on component side to facilitatecomponent placement. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board Row and column legends provided
-
product
Plugbord
3682-2
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.Interleaved buses pattern on wiring side only solder- coated for user convenience.Bus outline silkscreened on component side to facilitatecomponent placement. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board Row and column legends provided
-
product
Search Receiver
KMF 1
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR KMF 1. The KMF 1 search receiver is used according to the step voltage method. The cable line is scanned with two measurement probes that can be dismantled during transport. The battery-operated device is also suitable for locating multiple consecutive sheath faults.* Battery mode* Zero point compensation* accurate location of cable sheath faults* battery test
-
product
50 GHz Digital Setp Attenuator
PE43508
The PE43508 is a 50Ω, HaRP™ technology-enhanced, 6-bit RF digital step attenuator (DSA) that supports a wide frequency range from 9k to 50 GHz. It supports 1.8V control voltage and optional VSS_EXT bypass mode to improve spurious performance, making this device ideal for test and measurement, point-to-point communication systems, and very small aperture terminals (VSAT).
-
product
JTAGulator 24-Channel Hardware Hacking Tool
32115
On-chip debug (OCD) interfaces can provide chip-level control of a target device and are a primary vector used by engineers, researchers, and hackers to extract program code or data, modify memory contents, or affect device operation on-the-fly. JTAGulator is an open source hardware tool that assists in identifying OCD connections from test points, vias, or component pads on a target device.
-
product
Cable/Harness Tester
IST-380
IST Information Scan Technology, Inc.
THE IST MODEL 380 is a portable, stand-alone cable/harness tester for testing any cable up to 128 points. It detects opens, shorts, and miswires within one second by comparing the test result with the golden file or the data learned from a sample good cable. The error messages can be shown on the LCD display or printed out on a printer with the correct wire list needing reworking.
-
product
Design for Testability (DFT Test)
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
product
Very High Density Fiber Tap
Flex Tap VHD
Keysight Network Applications and Security
Flex Tap VHD is a modular, very high density fiber tap available, offering up to 36 taps in a 19 inch 1U space, to reduce IT costs while helping ensure availability of security and business critical applications. Network taps (test access points) are a key part of the access layer of a visibility architecture because they are an unobtrusive way to capture monitoring data. They offer comprehensive traffic visibility for network monitoring and security tools that do not introduce points of failure in the network. Ixia has a large variety of network taps on the market today, offering speeds from 1Gbps to 100Gbps, single and multi-mode, as well as different fiber types and support for Cisco bidirectional (BiDi) transceivers.
-
product
40N Switch Tester Coupling Implement Shell Pressure Test Device
CX-F01
Shenzhen Chuangxin Instruments Co., Ltd.
This device is according to the IEC60320-1 standard requirement to design. Appliance inlets designed for surface mounting and having a shroud of metal, are compressed in an appropriate test apparatus, an example of which is shown in figure 20. The spherical end of the jaws shall have a radius of 20mm±1mm. A force of 40N±2N shall be applied for 60s±6s through the jaws to the most unfavourable point half-way up the outer surface of the shroud, in a direction perpendicular to the axis of the shroud. After the test, there shall be no deformation or loosening of the shroud such as will impair the further use of the appliance inlet.
-
product
Energized Cable Sensor
The purpose of the Energized Cable Sensor is to allow the lineman to readily determine whether a URD cable is energized. The sensor consists of an amplifier which is designed to give a meter reading when the small AC voltage between the semi-conductive sheath and the concentric neutral of the energized URD cable is applied to the test probe. The amplifier is housed in a rugged phenolic case. Sensor may be used to check for energized condition on concentric-neutral cable below an elbow without test points. At cable mid-span (left), hose clamps bridge all strands of concentric neutral at the test location. Sensor’s neutral lead clips to one of the hose clamps. Tip on probe lead contacts only semi-conductive cable sheath to test for voltage presence.
-
product
Fretting Tester
FFT Series
Fretting wear is a test where surface damage occurs between two contacting surfaces experiencing oscillatory displacement of small amplitude. At the contact point, lubricant/coating is squeezed out or the low amplitude motion does not permit the contact area to be re lubricated/ debris dislodge resulting in serious local wear occurs. This type of wear causes two-body abrasion, adhesion and/or fretting fatigue wear.
-
product
Plugbord
3682-4
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers. Interleaved buses pattern on wiring side, solder coated for user convenience. Overall ground plane with clearance around each hole on component side. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board. Row and column legends provided.
-
product
CamTrac Z-Axis Test Fixture Kits
CT Serie
The CT Series Mechanical Kits, utilizing the patented CAM mechanism1, offset the same precision linear motion. The 'Z' axis motion is ideal for a larger point count mechanical test applications.The CT Series features a hinged 3/8" FR4 probe board, tooling holes for precision alignment, removable sides, precision shafts and cam slide block assemblies, and a pan latch assembly.
-
product
QuadraPaddle Signal Modules
The versatility of VPC's QuadraPaddle twin female contacts provide four beams per end to ensure signal integrity from instrumentation to the Unit Under Test (UUT).Twin male contacts interconnect to ribbon cable, headers, and other standard connectors.Makes system configuration a simple “plug & play” operation and delivers high density, high performance interconnectivity at a lower cost per point.